![sparkbox ek sparkbox ek](http://www.heritagemachineworks.com/uploads/7/1/4/4/7144916/7557411.jpg)
The rotation sensor can be mounted either on the main housing or on the lid depending on the direction of rotation. Determine the direction of rotation of the shaft. Damaging these surfaces will destroy the shaft seal. Thread the shaft as far as possible into the shaft.
SPARKBOX EK INSTALL
Unpack the mrs00 Rotation Sensor and the mrs00-ek Housing Kit and check the supplied parts with the parts list on page 3 of drawing Install the drive shaft (item ) in the machine s output shaft.
![sparkbox ek sparkbox ek](https://i.pinimg.com/originals/9e/b7/a7/9eb7a782679de50aa081b373844594e7.jpg)
The following steps are required to install the housing. See drawing 03 in Appendix for an exploded view of the enclosure with item numbers and mounting details. The direction of the rotating shaft must be known. A field interconnect must be located within.8m of the rotation sensor 3.
![sparkbox ek sparkbox ek](https://www.sparklebox.co.uk/wp-content/uploads/1-9204.jpg)
Excessive eccentricity will cause excess bearing wear or damage 2. It is extremely important to ensure this hole is centered and parallel to shaft. The shaft of the rotating device must be drilled and tapped with a ½ x 3 threaded hole to a depth of at least.5. Mounting using the mrs00-ek The following is required before attempting installation. The mrs00-ek is a free-standing enclosure that hangs from the drive shaft of the device. Installation The rotation sensor can be mounted using a fabricated bracket or a factory manufactured enclosure kit, the mrs00-ek.
SPARKBOX EK SERIAL NUMBER
There are 2 indicator lamps: Description Color Flash Rate Operation Status Green Ok, no communications Ok, communication active Power on self test fault Calibration parameter fault Firmware fault Serial number fault Rotation Red - Flashes whenever a code wheel magnet crossing is detectedĩ mrs00 Rotation Sensor Technical Manual /4 This page intentionally left blank.ġ0 mrs00 Rotation Sensor Technical Manual /5 3. Description of Indicators CMC Industrial Electronics mrs00 Rotation Sensor STATUS ROTATION Figure - Illustration of Indicators The sensor requires no settings. When used with the mbc08 Bus Converter the device is Intrinsically Safe.ħ mrs00 Rotation Sensor Technical Manual /2 This page intentionally left blank.Ĩ mrs00 Rotation Sensor Technical Manual /3 2. The cable is terminated with an RJ- connector for direct connection to CMCIEL wiring accessories. Each sensor comes complete with 2 meters of heavy-duty industrial cable rated for use in direct sunlight. The sensors are packaged in an industrial grade plastic housing utilizing a fully potted construction. Power for the sensor is supplied by the bus system. Communications utilize the Dallas -Wire bus standard. Each sensor has a unique digital serial number and will be automatically recognized by CMCIEL Bus Converters. Alternately a high force magnet assembly, the mrs00-mg, is available to attach the code wheel to the machine s output shaft.
SPARKBOX EK FREE
The housing is free hanging and does not require any brackets or safety shields. A rugged shaft mounted housing, the mrs00-ek, is available to facilitate mounting to the machine s output shaft. The device uses a unique code wheel that attaches to the shaft with a single ¼ or 6mm screw. Measurements from to 000 RPM are possible. Overview The mrs00 Rotation Sensor is designed to determine the shaft speed of rotating devices.
SPARKBOX EK UPDATE
2Ĥ mrs00 Rotation Sensor Technical Manual /ii Revision Notes First Release JanuRevision A May, 2005 Miscellaneous text changes and update dimensions drawing Revision B Update mechanical installation details to include grommet mounting system Revision C Update illustration showing new code wheel Revision D ApAdd the mrs00-ek to the manual Revision E December 7, 200 Update exploded view drawing 03 Revision F January 24, 202 Update parts list drawing 03ĥ mrs00 Rotation Sensor Technical Manual /iii This page intentionally left blank.Ħ mrs00 Rotation Sensor Technical Manual /. 7 Figure 3 - Typical Fabricated Installations. 4 Table of Figures Figure - Illustration of Indicators. Overview Description of Indicators Installation Mounting using the mrs00-ek Mounting using a fabricated bracket Communications Specifications. 0678, Revision F December CMC Industrial Electronics Ltd.ģ mrs00 Rotation Sensor Technical Manual /i Table of Contents. 1 ROTATION SENSOR -WIRE INTRINSICALLY SAFE mrs00 mrs00 Rotation Sensor Document No.